Warum die Neigung die tatsächliche Dachfläche verändert
Multiply length by width and you get the building's footprint, not its roof area. A sloped roof is a tilted plane, and a tilted plane covering the same footprint always has more actual surface than a flat one — the steeper the slope, the more material it takes to cover it. Pitch is expressed as rise over a 12-inch run, so a "6:12" roof rises 6 inches vertically for every 12 inches it runs horizontally.
Pitch multiplier = √(1 + (rise ÷ 12)²)
6:12 pitch: √(1 + (6/12)²) = √1.25 ≈ 1.118
A 40 × 30 ft footprint (1,200 ft²) at a 6:12 pitch works out to 1,200 × 1.118 ≈ 1,342 ft² of actual roof surface — about 12% more material than the footprint alone would suggest. Steeper roofs push that multiplier higher still; a 12:12 pitch (a 45-degree roof) has a multiplier of about 1.414, adding over 40%.
Von Quadratmetern bis zu Bündeln
Roofing is priced and ordered in "squares" — 100 square feet of coverage — and each material has its own typical coverage per bundle or unit. Asphalt shingles are the most common: a standard bundle covers about 33.3 ft², so three bundles make one square.
| Material | Abdeckung pro Paket |
|---|---|
| Asphaltschindeln | ~33.3 ft² (3 bundles/square) |
| Holzschindeln | ~25 ft² (4 bundles/square) |
| Schiefer / Tonfliesen / Metall / Gummi | ~100 ft² (1 bundle/square) |
Fortsetzung des obigen 1.342 ft²-Beispiels mit Asphaltschindeln und einer Abfallmenge von 10 %:
1,342 ft² × 1.10 (waste) ≈ 1,476 ft²
1,476 ÷ 33.3 ≈ 44.3 → 45 bundles (rounded up)
≈ 14.8 roofing squares
Wie viel Abfall ist einzuplanen?
A simple gable roof with few cuts can often get away with 10% waste. Roofs with more hips, valleys, dormers, skylights, or chimneys need more — 15% to 20% is common — because every seam and penetration means extra cutting and overlap that a flat rectangle calculation doesn't account for. Ridge caps, starter strips along the eaves, and underlayment add to the material list on top of the field shingles, so treat the bundle count here as the core estimate and build in room for those extras when pricing a job.
Schätzung der gesamten Projektkosten
Material cost = Roofing squares (with waste) × Price per square
Total cost = Material cost + Labor cost
Der Materialpreis pro Quadratmeter variiert je nach Produkt enorm – Asphaltschindeln liegen am erschwinglichen Ende, während Schiefer und Stehfalzmetall ein Vielfaches mehr pro Quadratmeter kosten. Arbeitsleistungen werden in der Regel als eigenständiger Einzelposten ausgeführt, der oft von der Dachneigung und -höhe sowie von der Fläche beeinflusst wird, da die Arbeit auf steilen oder hohen Dächern langsamer und riskanter ist.
Andere Teile eines Projekts messen
Für Bodenbeläge, Verkleidungen oder allgemeine Flächenabnahmen über das Dach hinaus ist dieQuadratmeterrechnerBehandelt rechteckige, kreisförmige und unregelmäßige Räume Schritt für Schritt auf die gleiche Weise.