Neden perde gerçek çatı alanını değiştiriyor?
Multiply length by width and you get the building's footprint, not its roof area. A sloped roof is a tilted plane, and a tilted plane covering the same footprint always has more actual surface than a flat one — the steeper the slope, the more material it takes to cover it. Pitch is expressed as rise over a 12-inch run, so a "6:12" roof rises 6 inches vertically for every 12 inches it runs horizontally.
Pitch multiplier = √(1 + (rise ÷ 12)²)
6:12 pitch: √(1 + (6/12)²) = √1.25 ≈ 1.118
6:12 eğimde 40 × 30 ft'lik bir ayak izi (1.200 ft²), 1.200 × 1.118 ≈ 1.342 ft²'lik gerçek çatı yüzeyine karşılık gelir; bu, tek başına ayak izinin önerdiğinden yaklaşık %12 daha fazla malzemedir. Daha dik çatılar bu çarpanı daha da yükseltiyor; 12:12'lik bir eğim (45 derecelik bir çatı) yaklaşık 1,414'lük bir çarpana sahiptir ve bu çarpan %40'ın üzerindedir.
Metrekarelerden paketlere kadar
Roofing is priced and ordered in "squares" — 100 square feet of coverage — and each material has its own typical coverage per bundle or unit. Asphalt shingles are the most common: a standard bundle covers about 33.3 ft², so three bundles make one square.
| Malzeme | Paket başına kapsam |
|---|---|
| Asfalt zona | ~33.3 ft² (3 bundles/square) |
| Ahşap zona | ~25 ft² (4 bundles/square) |
| Kayrak / kil kiremit / metal / kauçuk | ~100 ft² (1 bundle/square) |
Yukarıdaki 1.342 ft² örneğine asfalt kiremitler ve %10 atık payı ile devam edersek:
1,342 ft² × 1.10 (waste) ≈ 1,476 ft²
1,476 ÷ 33.3 ≈ 44.3 → 45 bundles (rounded up)
≈ 14.8 roofing squares
Ne kadar atık planlanmalı
A simple gable roof with few cuts can often get away with 10% waste. Roofs with more hips, valleys, dormers, skylights, or chimneys need more — 15% to 20% is common — because every seam and penetration means extra cutting and overlap that a flat rectangle calculation doesn't account for. Ridge caps, starter strips along the eaves, and underlayment add to the material list on top of the field shingles, so treat the bundle count here as the core estimate and build in room for those extras when pricing a job.
Toplam proje maliyetini tahmin etme
Material cost = Roofing squares (with waste) × Price per square
Total cost = Material cost + Labor cost
Metrekare başına malzeme fiyatı, ürüne göre büyük ölçüde değişiklik gösterir; asfalt kiremitler uygun fiyatlı uçta yer alırken, arduvaz ve dik dikişli metal, kare başına birkaç kat daha pahalıya mal olur. Dik veya uzun çatıların üzerinde çalışmak daha yavaş ve daha riskli olduğundan, işçilik genellikle kendi kalemi olarak çalışır ve genellikle alan kadar çatı eğimi ve yüksekliğinden de etkilenir.
Bir projenin diğer bölümlerinin ölçülmesi
For flooring, siding, or general area takeoffs beyond the roof itself, the square footage calculatorDikdörtgen, dairesel ve düzensiz alanları aynı adım adım işler.